On this page below you can get additional professional points with regards to Installing A Bathtub.
Installing a bathtub isn't exactly brain surgery, however it does need solid plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old bath tub with a new one is also a reasonably tough task. If the old bathtub is readily obtainable, the job can relocate immediately; if you have to open up a wall surface to get rid of the old tub as well as position the brand-new bath tub, the task is a lot harder. In either situation, the project is within a home handyman's abilities, although you will require an assistant to leave the old tub as well as embeded in the brand-new one. Make sure you have actually qualified on your own for the job and also fit attempting it. Instead of hiring a service provider to take control of a halfway-completed project, it is better to think about utilizing one prior to you start. Chances are you may need a professional plumber to make tube connections.
This article will aid you set up a new tub in your shower room if you have already gotten a new tub and also don't require to transform the plan of your previous supply of water pipes.
Your devices as well as material list should consist of the following:
Planning for the Installment
To start with, the sustaining frame supplied with the bath ought to be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets unit to prevent strain on the bathtub.
Fit the adaptable faucet ports to the bottom of both faucets making use of 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its last position.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of getting rid of the existing faucets can be rather troublesome as a result of the limited accessibility that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a towel prepared for the staying water that will originate from the pipelines. Once the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old securing compound.
Before moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Tub
Making use of the two wooden boards under its feet, place the bathtub in the needed setting. The wood boards are helpful in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four little points.
The following objective is to make sure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bath tub till the spirit level checks out degree.
To set up taps, fit all-time low of the outermost adaptable tap adapter to the ideal supply pipe by making a compression sign up with; after that do the same for the various other tap.
Switch on the supply of water and check all joints and new pipework for leaks and tighten them if essential. Fill up the bathtub as well as additionally examine the overflow outlet as well as the typical outlet for leakages.
Ultimately, repair the bath paneling as defined in the manufacturer's user's manual. Tiling and also sealing around the tub should wait up until the tub has actually been utilized at the very least once as this will settle it right into its last position.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin making sure that the washing machines are in place in between the tap as well as the sink. Secure the tap in position with the maker supplied backnut. When the tap is safely in position, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical faucet connectors. The former type needs to be connected to the faucet ends initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split an inflexible seal, causing the water to penetrate the wall surface between the bath and also the tiling, causing difficulties with wetness and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your fixtures and fittings. They are offered in tubes and cartridges, as well as are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the bath tub with water prior to securing, to enable the movement experienced when the tub is in use. The sealant can fracture relatively early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally easily available on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that review about Tools You Need to Install a New Bathtub when doing a search on the search engines. You should take the time to share this content if you liked it. I am grateful for your time. Come back soon.
Quick relief? Dial!